Kodi Version 16 and above PVR Stalker Client Setup Instructions for NFPS Server

[kens]

Kodi Version 16 and above PVR Stalker Client Setup Instructions

Get the most recent version of Kodi from the Playstore (Android) or
for any Platform here -> hxxps://kodi.tv/download/

* (All I/P Addresses shown as hxxp or hxxps, replace with http or https -(No Live Links Rule))

-Install and run Kodi

-Go to System Settings/Add Ons/My Add Ons/PVR Clients/Stalker Client.

***Note
The KODI Settings screen has 4 levels of access, located at the bottom left of the screen. To access all required settings, click the Tab until “Advanced" or "Expert” level is indicated.

-Select Configure

-Set Portal 1 and Connection timeout to 120

-Enter your MAC#
Format Example( 00:1A:78:xx:xx:xx ) Replace the x’s, with your last digits from your STB’s MAC# or your PC /Apple/RasPi/Fire/DL-T/etc. MAC# …or
make up a random number in HEX from 00 to FF (Example: 2A:B9:43)

-Leave the Time Zone as is.

-Enter your Server Address (Info located from your donation information at Papiao
here -> hxxps://papiao.is/main/search_nfps

*** Note Kodi 16 doesn't handle URL forwarding
- For NFPS,
If the server is 1.iptvprivateserver.tv then you would use hxxp://portal1.iptvprivateserver.tv/stalker_portal/c/index.html
If the server is 5.iptvprivateserver.tv then you would use hxxp://portal5.iptvprivateserver.tv/stalker_portal/c/index.html
etc.

-Enter your Login & Password
(Login & Password both require your donation#)

-Enter a random Serial Number - should be a minimum 13 digit number (I use 6 numbers/1 Letter/ 6 numbers)

-Enter a random Device ID - Should be a minimum 12 digit number (I use numbers only)

*(Token/Device ID2/Signature should be blank (at this time they are redundant fields))

EPG info:
-Set to Prefer XMLTV

Remote URL:
URL Address :
hxxp://nfps.**********

Save your settings by clicking OK, then Enable Stalker by clicking “Enable”.


* You Must now go to Papiao Site and "Associate" your MAC# you entered above, with your Donation#.
Once you have done that...


Go back to Settings/TV - General Tab
-There are 3 settings regarding using Channel Numbers and Groups and Sync from the Back End. Enable all 3.

-Then Select "Enable".

Kodi should now attempt to connect. A message window in the top right corner of the screen will appear.
It will say "Loading Channels from Clients (if successful, Kodi will Include a "TV" Icon on the Menu Bar)
It will then Attempt to load the Guide. Let the system load everything before you attempt to watch TV.
If there is a problem, (Error Message at bottom right of Screen), Shut down and Restart KODI.

If you still have problems, post your results.


FYI - IPTV Reset is used to clear Device ID Information stored in the server ONLY.

You can only do this twice in a 24hr. period, so dont over use this function to try to correct a problem unrelated to your Dev ID1 Information.
(Next time you connect, it records the Device id you have entered in your configuration settings).


Good Luck and Happy Viewing
/kens

[hmohssin]

Thank you for sharing that :)

[Driver]

Could you please set up a tutorial for iksrocket please?

[Driver]

Hello Crazed, your link is sending me to a nice Beatles song! Any help on my post will be much appreciate it http://iptvtalk.net/showthread.php?23417-Stalker-10-2-4-R2-Error

[crazed 9.6]

Hello Crazed, your link is sending me to a nice Beatles song! Any help on my post will be much appreciate it http://iptvtalk.net/showthread.php?23417-Stalker-10-2-4-R2-Error

i checked your post bud.... i have no way to know

[habbok]

Well after a try all the ideas possible I'm still unable to use KODI and Stalker PVR build in

[kens]

Post more info?\

your equipment, service, platform(kodi/stb/mag/etc)
your step by step progression
your results

(and post in the kodi discussion thread!)

/kens

[sona]

I did all the steps on my MX3 and on Minix Neo8, but can not understand why on my Minix Neo the guide doesnt load at all, but it works on MX3 box? I setup both boxes the same way with the same steps with two different mac and seperate papiao accounts. any help will be appreciated

[ilan]

Are both boxes running the same version of Kodi? What remote address are you using for the guide?

[sona]

mx3 is running 15.2, and minix neo is running 16.1

this is what I put for the guide:

http://papiao.is/main/EPG/mac/**:**:**:**:***:**/donation/*************/fname/NFPSF1

[ilan]

That is an ancient, non-working method. Choose remote URL and use



http://nfps.epg.n i n j a


(Eliminate the spaces in the ninja portion of the address.)

If that doesn't do it, use this address



https://raw.githubusercontent.com/psyc0n/epgninja/master/guide.xml

[BIGMANNYC]

hello kens i read this and followed as you directed and im still getting the authenticaton error on bottom right every time its about to load chs from clients happens only with jarvis , it was working well with lisengard but no epg so i tried to install the epg thing from clairvoyance and i saw some other type of epg and it changed the channels and the remote keyboard was not working well after that so maybe that epg was for jarvis? and didnt work well with lisengard? so i uninstalled lisengard an desided to try jarvis again but every time i try jarvis i cant get the channels to load even after changing the server info and all... guess ill have to go back to lisengard for now...any sugestions? thx

[expatter]

hello kens i read this and followed as you directed and im still getting the authenticaton error on bottom right every time its about to load chs from clients happens only with jarvis , it was working well with lisengard but no epg so i tried to install the epg thing from clairvoyance and i saw some other type of epg and it changed the channels and the remote keyboard was not working well after that so maybe that epg was for jarvis? and didnt work well with lisengard? so i uninstalled lisengard an desided to try jarvis again but every time i try jarvis i cant get the channels to load even after changing the server info and all... guess ill have to go back to lisengard for now...any sugestions? thx


Jarvis works fine and so does Krypton for that matter. It you are using anything from clairvoyance...well, that's a problem to begin with. That is no longer working with this service at all and has not for several months now. Going backwards doesn't make much sense as things improve with newer versions as codes are fixed and updated.

I would reommend you stay with at least Jarvis. Set the epg scope to xmltv only and use the address that is listed in the thread for NEW EPG OPTION and you will have a working epg. If your channels won't load then close kodi and go to papiao and do an IPTV reset and then wait about 10 to 15 minutes and restart kodi.

YES, the new epg methods discussed in the forum work with Jarvis.

If you are getting an authentication error then you have made an input error somewhere. Try again. Make sure you enter the MAC, ID, Passwords exactly.

Another reason you might get the authentication error is if you also have the Stalker IPTV video addon enabled. You can't have both enabled at the same time. If you have the video addon installed, disable it and then do as suggested earlier and IPTV Reset at papiao. Wait a bit and restart kodi.

And you should have it working. At least the channels and guide will load. Now, if the channels are actually working...well, that's another story.

Just go slsowly and enter your data precisely. Do the reset. Wait. Restart kodi. Benefit.

[kens]

Did you change the server address format for kodi16 which is different if you are upgrading from 15?
/kens.
*Note
the backend stalker software also changed between 15 and 16, and I think the user credential information structure of the server database is different.
If you change your MAC#, the server will open a new user id structure based on the new version 5 format.
Worked for me a couple times

[bsmith999]

Hi I am getting following error:

Stalker client, authentication failure, retrying gain.

and a progress bar appears in the R.H Corner

Remote URL:
URL Address :
hxxp://nfps.********** (What information to fill for these stars.)

Thanks,

[pendlet]

Use this thread to setup your EPG

http://iptvtalk.net/showthread.php?25077-TV-Guide-(EPG)-for-US-UK-Canada-and-Latin-American-channels

but you need to make sure your connected to a server first and by the sounds of it your not.

Follow this thread to make sure your connected first. http://iptvtalk.net/showthread.php?23145-Kodi-Version-16-and-above-PVR-Stalker-Client-Setup-Instructions-for-NFPS-Server

[bsmith999]

I am getting authentication failure when i did exactly what you have said here.





Kodi Version 16 and above PVR Stalker Client Setup Instructions

Get the most recent version of Kodi from the Playstore (Android) or
for any Platform here -> hxxps://kodi.tv/download/

* (All I/P Addresses shown as hxxp or hxxps, replace with http or https -(No Live Links Rule))

-Install and run Kodi

-Go to System Settings/Add Ons/My Add Ons/PVR Clients/Stalker Client.

***Note
The KODI Settings screen has 4 levels of access, located at the bottom left of the screen. To access all required settings, click the Tab until “Advanced" or "Expert” level is indicated.

-Select Configure

-Set Portal 1 and Connection timeout to 120

-Enter your MAC#
Format Example( 00:1A:78:xx:xx:xx ) Replace the x’s, with your last digits from your STB’s MAC# or your PC /Apple/RasPi/Fire/DL-T/etc. MAC# …or
make up a random number in HEX from 00 to FF (Example: 2A:B9:43)

-Leave the Time Zone as is.

-Enter your Server Address (Info located from your donation information at Papiao
here -> hxxps://papiao.is/main/search_nfps

*** Note Kodi 16 doesn't handle URL forwarding
- For NFPS,
If the server is 1.iptvprivateserver.tv then you would use hxxp://portal1.iptvprivateserver.tv/stalker_portal/c/index.html
If the server is 5.iptvprivateserver.tv then you would use hxxp://portal5.iptvprivateserver.tv/stalker_portal/c/index.html
etc.

-Enter your Login & Password
(Login & Password both require your donation#)

-Enter a random Serial Number - should be a minimum 13 digit number (I use 6 numbers/1 Letter/ 6 numbers)

-Enter a random Device ID - Should be a minimum 12 digit number (I use numbers only)

*(Token/Device ID2/Signature should be blank (at this time they are redundant fields))

EPG info:
-Set to Prefer XMLTV

Remote URL:
URL Address :
hxxp://nfps.**********

Save your settings by clicking OK, then Enable Stalker by clicking “Enable”.


* You Must now go to Papiao Site and "Associate" your MAC# you entered above, with your Donation#.
Once you have done that...


Go back to Settings/TV - General Tab
-There are 3 settings regarding using Channel Numbers and Groups and Sync from the Back End. Enable all 3.

-Then Select "Enable".

Kodi should now attempt to connect. A message window in the top right corner of the screen will appear.
It will say "Loading Channels from Clients (if successful, Kodi will Include a "TV" Icon on the Menu Bar)
It will then Attempt to load the Guide. Let the system load everything before you attempt to watch TV.
If there is a problem, (Error Message at bottom right of Screen), Shut down and Restart KODI.

If you still have problems, post your results.


FYI - IPTV Reset is used to clear Device ID Information stored in the server ONLY.

You can only do this twice in a 24hr. period, so dont over use this function to try to correct a problem unrelated to your Dev ID1 Information.
(Next time you connect, it records the Device id you have entered in your configuration settings).


Good Luck and Happy Viewing
/kens

[ilan]

Usually something is configured incorrectly when you get that. Did you flesh out to the longer portal URL? There is another instruction sheet you can use to double check. Once you're certain everything is configured correctly, disable the PVR, do an IPTV Reset, wait at least 15 minutes and then enable it. Don't worry about configuring the EPG for the moment.

http://iptvtalk.net/showthread.php?24831-PVR-Stalker-(Kodi-Built-in)-Set-up-tutorial